Prophet Siege Tank (Pre-Supported)
.png)
.png)
$11.50 Prophet Siege Tank (Pre-Supported)
3D
Published 2025-12-01T15:03:16+00:00
Hulking war machines forged and assembled in the industrial world of Messis, Prophet Siege Tanks carry some of the most powerful weapons in the entirety of the Lost Legion arsenal, serving either as tank destroyers or high-caliber ordnance .
This kit includes all the files necessary to print an Prophet Siege Tank:
- The vehicle's core acts as both an ammo bay and crew compartiment, and the interior is fully detailed for hobbyists who enjoy painting the inside of their tanks. A pilot with a separate helmet is included too. The rear ramp is printed in place, but is actually a separate piece and can be moved if left unglued, including a 3x2mm magnet slot so it snaps into position.
- Tracks are a single piece each for ease of assembly, but do have three 3x2mm magnet slots on the side, which fit with those in the side armour to make the kit more compatible with other vehicles from the range.
- The top of the vehicle snaps into place, and can be left unglued to be able to see the vehicle's interior at any point or swap it out. It does have four 3x2mm magnet slots that match with those on the vehicle's core, but normally these shouldn't be necessary since the fit is tight enough. They can still be helpful if the piece has warped or shrunk too much.
- The top hatch is also has a standard-sized, with the kit including a flat one, but being fully compatible with the Pintle-mounted Upgrade Pack for a wide variety of weapon options.
- There is an optional dozer blade designed to be bulkier than those on other tanks, and has four 3x2mm magnet slots to make it fully optional.
- Three weapon options: a demolition bombard, a magna lascutter or a magna laser array, all of which include two slots for 5x2mm magnets so they are interchangeable and can be rotated.
- To allow for the weapons to be swapped at any point, the reloading system also has a slot for a 5x2mm magnet. There is a choice between two reloading claw poses and an open or closed shell feed for the demolition bombard, or a power source with cables for the laser weapons.
- The front shield is also fully optional and has two different variants to allow for variety within a collection. It also has two 3x2mm magnet slots to make it easier to swap the weapons without it getting in the way.
- Two hull-mounted basic combi-guns. These share the same fitting mechanism as all the combi-guns in the Lost Legion range but, since the hull opening is quite small, can only be replaced with the more compact ones.
- Since the four magnet slots for the dozer blade and two for the front shield would be exposed, I've included a 3x2mm filler if you'd rather not use those options. That said, this kit includes a lot of optional magnetisation opportunities, which can take a while to set up. For simplicity's sake you might want to glue some of the parts instead of fully magnetising everything.
- A spare demolition bombard shell for any kitbashers who want to have fun (yes, it does fit inside the barrel).
Both pre-supported and unsupported .stl files included for each piece, as well as .ags files so you can manipulate the supports using Runebrace.
I printed mine in Anycubic's gray ABS-like V2 resin (water-wash) on a Elegoo Saturn 3 printer with 0.04mm layer height, 2.4 exposure time, 6>7 lift distance, 45>100 lift speed, 180>65 retract speed and 0,5 wait after lift. There were 5 burn in layers with 25 exposure time and 7 transition layers. However, these values can change significantly between printers and resins, so trust your own experience.
I test printed all the bits available a few times to make sure the pre-supported files worked.
| Date de publication | 01/12/2025 |
| Price | $11.50 |
As the designer, I tested all bits available to make sure everything worked well